In this tutorial, learn how to use the iRobot Create 2 to drive around and stream video over the wireless network. We will control the iRobot Create 2 via WiFi from our laptop computer, using a PlayStation controller to steer. Part one covers hardware setup and prerequisites.

Tutorials in this series:

1.0 Hardware Overview

To build your own teleoperated iRobot Create2 you will need the following hardware:

Using a Gumstix COM (Overo or DuoVero):

 

Using a Pepper SBC (43R or 43C):

 

You can download the source files for this project here.

1.1 Hardware Setup with a Pepper SBC (43R or 43C)

Using a Pepper SBC dramatically reduces the number of parts used, using the Gumstix iRobot Create 2 cable further reduces the bundle of wires.  The 3D printed bin is available with the source files here.  STL’s for the complete bin as well as a 6-piece variant is available for those with smaller printers.

20151007_095944

 

1.1.1 Removed unused components

First remove the green faceplate to gain access to the mini-DIN connector.  You may use a 1/4″(14mm) drill bit to clear a hole for the connector.  Next loosen the 4 screws to the battery cover:

20151005_121424

 

After removing the battery cover, loosen 4 more screws to remove the brush holder:

20151005_121227

 

Now you will have room to put your 3D printed bin!  Screw the Pepper onto the 3D printed bin, attach the USB webcam to the USB port, and the Gumstix Create 2 Cable as shown:

20151005_115847

Connect the JST-XH 2S connector to the matching connector on the Pepper, and the UART connector to pin 98(brown) and 97(orange), this is UART2 on the Pepper.

 

Next, replace the clear bottom piece of the stock dust bin with your new 3D printed bin:

 

20151005_121559

 

Finally, connect the WiFi antennae and feed the USB webcam cable and mini-DIN cable through where the plastic grille used to be:

20151005_121912

 

And you’re done, move onto section 2.0: Creating a Catkin Workspace!

1.2 Hardware Setup with a Gumstix COM and expansion board

1.2.1 Remove unused components


Remove the filter, cover, fan shroud and motor from the bin on the Create 2 to make room for the electronics.

1.2.2 Wire the batteries and add a power connector

irobot_tutorial_1_2
Wire four AA batteries in series to power the COM and electronics. You can also solder a switch on the positive wire to make it easier to cut power to the electronics.

1.2.3 Connect the hardware

irobot_tutorial_1_3
Connect the wireless antenna to the COM, and then connect the COM to the expansion board. Plug the USB port into the Tobi’s USB Host port before connecting the batteries to the Tobi’s power connector.

1.2.4 Mount the hardware inside the bay

irobot_tutorial_1_4
Removing the cover from the bay reveals an opening where you can feed the antenna and USB hub’s cable through, as well as a place to mount the power supply switch if you added one in step 2. The Tobi, COM and batteries can all go inside the bay.

1.2.5 Mount additional hardware on top of the Create 2

irobot_tutorial_1_5
Insert the bay back into the Create 2, find somewhere to secure your webcam and you’re set! Make sure your Create 2 is fully charged before teleoperation.

2.0 Create a Catkin Workspace

First, you may need to install Catkin for your version of ROS:

$ sudo apt-get update
$ sudo apt-get install ros-%ROS_DISTRO%-catkin# ex: for ROS Jade
$ sudo apt-get install ros-jade-catkin

Create and initialize a Catkin workspace on your host machine if you don’t already have one. There is an excellent set of tutorials on how to do this at http://wiki.ros.org/catkin/Tutorials/create_a_workspace.

3.0 Installing ROS Packages on Host

One of the main advantages of ROS is the large collection of open-source packages written and maintained by its community. Learning to install and use these packages can speed up development of your robot considerably.

3.1 Installing gscam from Source

First, install some prerequisites:

$ sudo apt-get install libgstreamer0.10-dev ros-%ROS_DISTRO%-camera-calibration-parsers ros-%ROS_DISTRO%-camera-info-manager libusb-dev libspnav-dev

We will build and install the gscam package from source, as it will be needed later on for streaming video from a USB webcam.

Note: my catkin workspace path is ~/catkin_ws. This was created above following the create a workspace tutorial

Source the following environmental variables:

$ source /opt/ros/%ROS_DISTRO%/setup.bash
$ source ~/catkin_ws/devel/setup.bash

cd to your catkin workspace source directory:

$ cd ~/catkin_ws/src

git clone the source files:

$ git clone https://github.com/ros-drivers/gscam.git

cd to the top of your catkin workspace and build the package:

$ cd ~/catkin_ws
$ catkin_make

Note: catkin_make builds every package under the src directory in the catkin workspace

3.2 Installing Joystick Drivers

In order to use the Playstation controller, we’ll need the joystick drivers package:

$ sudo apt-get install ros-%ROS_DISTRO%-joystick-drivers

# ex: on ROS Indigo
$ sudo apt-get install ros-indigo-joystick-drivers

 

Next we will create the irobotcreate2 package from scratch in part two.